From the first tense to the master's sceptical eyes, the touch of the joystick, to his leisurely and skillful, skillful, complex action. From the first butter to the independent maintenance machine, the troubleshoot to solve the machine, from the trembling earth to the first shovel to easily cope with a huge dump convoy. We have gone through so many first times! So many first time, so many interesting stories, the story is so many experiences and lessons, we grew up in so many many of the first time, we and the excavator, and we talk about how to drag the car.
Long ago, I saw some teacher Fu on the tray, feeling and walking the same way, the whole process of the whole process is fluent, very admired, very admired. But when the opportunity finally came to his own body, that tension, don't mention it. The tow truck arrived, the master was not around, the heart really wanted to tell the boss the truth, I'm sorry, I didn't go to the tray, But it's too disgraceful, the duck on the shelf, courage, hard scalp on it. It is much more beautiful, the whole process of the impression of the whole process, starting to adjust the machine and car body straight, guide wheel forward, drive the wheel in the rear, the car forward, slow slow climb, the heart beat that fast, the car's elevation is fast 30 of the heart is fast jumping out when the angle is fast 30 of the elevation is quickly out of the heart out of the car out of the angle of the angle is fast jumping out when the elevation of 30 of the elevation is fast jumping out of the angle of the lift angle is quickly 30 of the elevation of the angle is quickly jumping out of the heart. Come on, continue to expand the angle, feel you can, spin 90, the center of gravity down, the bucket supports the ground, halo! The car is not up, the original advance is not enough, the excavator and body contact is not enough, and the warp is not high enough. Walking on the side of the pedal arm to the level of the machine and pallet car level, already most of the contact body, at this time the excavator has no angle, stable standing on the trailer, I feel very comfortable in my heart, I think very simple, so lift the arm, a fierce rotation, suddenly the body of a sudden, shocked the people in a cold sweat, I busy slow speed, etc. The trailer shaky a few times, calm down, and then adjusted, feel the position of the same, just fist up the small arm, tighten the shovel, slowly put down, the feeling is already in the end, the bucket oil seal and the car board has a certain distance, no harm, then shut the machine, lock the car. To the bottom, the left side of a point on the outside, exposing 20 common. The right side is too far away from the right side, there is a distance from the right edge of the car, and the arm is not very good, although it is not very good, but the first time, do so is satisfied, the time is long, sometimes the work needs, the machine needs to move back and forth a few times, the opportunity on the tray is also more, the courage is also big, now back up The first experience is still funny, my personal experience of the pallet, to give you a reference, and also welcome criticism and supplement.
First, keep a steady state of mind, don't be afraid, don't be affected by the onlookers, tell yourself to walk on the tray, walk peacefully, we all climb over the steep slope, and fear such a small angle. But do not be arrogant with a show of mind, too confident is not a good habit, do not feel inferior and not good.
Second, observe the terrain, the level of the pallet car, it is better to take a wooden square underneath the trailer to prevent the trailer moving in the course of climbing, especially the downhill, to see if there is a high pressure line above the trailer. Observe the width of the trailer, the general trailer is 3 meters and 18,9 meters long. The body of the excavator is 3.2 on the side, and 10 centimeters on the other side will be enough, so that we can have a good idea. OK, the preparations are ready, and then the next step.
Third, adjust the excavator, the throttle or the gear position as far as possible to the low position, do not install the fast car hand, the safety and stability most important, and the slow motion is consistent and good. The machine weight is big, the movement is a little big on the trailer, the throttle is big, the movement is fast enough to be afraid, so it is necessary to crawl slowly to a certain angle to the excavator. It is similar to the trailer contact machine, slowly rotating, the right hand pressing the big arm hoisting car, and continuing to walk, this process if skilled and coherent. When the machine is in contact with the large area of the excavator and the car, the lift arm turns, continues to adjust to the appropriate position, in the rotation, the arm back shovel, as far as possible to prevent the transport from touching bridges and high pressure line, but also to prevent the transport process from bridge and high pressure line, but also to prevent transportation, but also to prevent the bridge and high pressure line in transport process, but also to prevent transport process, but also to prevent the bridge and high pressure line, but also to prevent transport process, but also to prevent the bridge and high pressure line, but also to prevent transport process, but also to prevent the bridge and high pressure line, but also to prevent transport process, but also to prevent the bridge and high pressure line, but also to prevent transportation, but also to prevent the bridge and high pressure line, but also to prevent transportation, but also to avoid Avoid damaging the bucket oil seal. Don't be too low. Don't touch the trailer board. Finally, stop the car and get off the car. Of course, get off the car. Of course, the two chains of the trailer can be done by the excavator. If you feel sure about it, don't make a swollen face as a fat man and put a man's iron plate. When it breaks, it's not worth it.
