I was a thirteen year old excavator. Last year, I was lucky to pack a stone field work. The surrounding tyres were full of rubble, and some of them were put on the back board of the dump truck. That's a man of Qi. Well, nonsense is not much said, on the topic, because I do not open the excavator, so the picture is not much, you forgive me.
1: Road, road is the most important, the road in the stone field is the most important, not to look more beautiful and beautiful, but must be flat, not pit wow wow, more can not be biased, must use the bottom of the bucket, can not leave the stone, small or not, because the stone road is hard bottom, there is a small stone tires may be broken, the situation should be fine, the situation need fine. The stone slag is spread over a layer, so as to make the surface smooth, so that the dump truck loves to reverse your car.
As we all know, the general stone factory is a few excavators together, all is to load the tonnage of the settlement of mechanical fees, dump cars want to go there who there, the road to go to the car is more natural, the advantage of excavators is also high.
Two: the working face is not only about the working face of the excavator, but also the working face of the dump truck. The platform selection must be correct, the platform is as flat and spacious as possible, to the condition that the platform is allowed to be allowed, and the top of the platform is flat with fine slag, so that the excavator can walk at will, adjust the machine position at any time, and reduce the friction between the track and the stone, will not hurt the caterpillar, the working face is flat, and the butt naturally will not blossom, I used to open a Komatsu 360 for two years. At any time, adjusting the position of the machine can also find the nearest distance between the stone and the car, shorten the loading time, improve the working efficiency, do not have a platform to play well on the place, this is the big taboo, it is said that here some may say that playing the platform on the stone is very troublesome, in fact, as long as you do a good number of things in the process of loading the car, a good number, one By loading the car, it will be almost the same if you use the bucket to sweep it. It is not a little bit more economical than the original turn around. The teachers are sure to understand this.
In addition, do not only leave the road of the dump truck, do not meet a soft place to dig down the dead, let you dig the fish pond, keep a level as much as the road, so that once you do not go in this road, you can easily and easily change the road. One more important thing is that once the car is found to reverse the distance, it is at any time in the most comfortable distance, so the car goes back and then comes down. The rest of the idle speed is not a little bit, the distance is short, and the driver is also willing to come and load the car. After a series of cycles, profits will naturally be higher than other excavators.
Three: the retreat of the platform, like the position of this excavator, it is sure to withdraw the platform. Some masters are all dumped on the two sides. I can only say ha ha. I all fix the platform behind the excavator in advance. When I load the car, the front car is filled, then the machine is retreated one step, and the fart after the flock is turned. The two corners of the stock, the material without platform, generally speaking, the car is full, the platform is also the same, only the rest of the car is in the middle of the point, the three five in addition to two to do. This will save labor and time, but not to do it.
Four: loading skills, this is the most important, the biggest taboo of the stone loading is that no matter the car dump dead, the front two or three must be light, as far as possible to load the bottom of the paving, from the front to the back to start loading, the middle of the block in advance to block the position of the baffle, to prevent the car crash during the process of rolling big stones to open the baffle, this It's disgusting.
To install uniform, large pieces and crushed material is mixed together, so that the weight, everyone is settled according to tonnage, so it is good for everyone, not in the top of the top, because in this way, it will roll down the top of the flapper, people will come to find trouble, even if you do not find trouble is also very bad. That's good.
When loading the car, do not grasp the full, too full in the process of turning in the process of falling down to the wheel, now people are very lazy no one is willing to go down to pick stones. At the time of turn, we must be at a constant speed, not to stop a sudden turn of rotation. Otherwise, the stone in the bucket will be scattered because of inertia. Even if it is suddenly found in the bottom, someone should calm down and turn over, even if it is transferred to the other side and do not stop above people. This is a big taboo, I have gone through many times and turned the past instead. It's okay. As soon as it stops, the stone comes down and hurts people. The experienced master must be very clear.
As far as possible to put the broken on it, so that in the process of transportation will not be easy to roll down, loading the car is not easy to drop stone, when I load the car, I never come down to pick up the stone. So everyone likes to look for me to load the car, so it is more natural than others, and then it is necessary to finish the car will have to look both sides of a firm beat, after the butt shot, to prevent material. Don't be careless. It's a dangerous thing. We had a car in the mine because a stone fell down the back of the rear wheel on the lower slope. The four tires were all scrapped and the side of the car rolled in the ditch.
After loading, I saw that there was gravel on the ground and swept aside.
To sum up, a series of details can be done a lot more a day than others, and not tired, the same brand tonnage time of the excavator, I at most a month more than more than 10000 tons more than others. The boss naturally likes me more, and gives me more pay.
